تخفیف‌ها و قیمت جشنواره‌ها در قیمت فروش در نظر گرفته نمی‌شود
توجه : برای فیلتر کردن نمایش ها در نمودار بر روی عنوان هریک کلیک کنید .
اسیلوسکوپ دیجیتال ۷۰مگاهرتز ۲کانال هانتک Hantek DSO5072PHantek DSO5072P Digital Oscilloscope, 70 MHz / 2CH
- 70 مگاهرتز 2 کانال + دیجیتال حافظه دار
- سرعت نمونه برداری 1GSa/S
- صفحه نمایشگر WVGA رنگی 7 اینچ
- فانکشن FFT
- اتصال به کامپیوتر با پورت USB
- 31 نوع اندازه گیری اتوماتیک
- USB FLASH
- ساخت چین
- ضمانت : یک ساله تعمیر
14,080,000 تومان
آماده ارسال مقایسهآیا قیمت مناسب‌تری سراغ دارید؟
بلیخیرموجود در انبار
اسیلوسکوپ ۷۰مگاهرتز ۲کانال هانتک Hantek DSO5072P
اسیلوسکوپ ۷۰مگاهرتز ۲کانال هانتک Hantek DSO5072P
- اسیلوسکوپ ۷۰ مگاهرتز ۲ کانال + دیجیتال حافظه دار
- سرعت نمونه برداری ۱GSa/S
- صفحه نمایشگر WVGA رنگی ۷ اینچ
- فانکشن FFT
- اتصال به کامپیوتر با پورت USB
- ۳۱ نوع اندازه گیری اتوماتیک
- USB FLASH
- ساخت چین
- ضمانت : یک ساله تعمیر
Specifications :
| Model | DSO5072P | ||
| Acquisition | |||
| Sample Rate | Real-Time Sample: 1GS/s Equivalent Sample: 25GS/s |
||
| Acquisition Modes | |||
| Normal | Normal data only | ||
| Peak Detect | High-frequency and randon glith capture | ||
| Average | Wavefom Average, selectable 4,8,16,32,64,128 | ||
| Inputs | |||
| Inputs Coupling | AC, DC, GND | ||
| Inpits Impendance | ۱MΩ±۲% ‖۲۰pF±۳pF | ||
| Probe Attenuation | ۱X, 10X | ||
| Supported Probe Attenuation Factor | ۱X, 10X, 100X, 1000X | ||
| Maximum Input Voltage | CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×); Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur. |
||
| Horizontal | |||
| Sample Rate Range | ۵۰۰MS/s–1GS/s | ||
| Waveform Interpolation | (sin x)/x | ||
| Record Length | ۴۰K | ||
| SEC/DIV Range | ۲ns/div to 80s/div | ||
| Sample Rate and Delay Time Accuracy |
±۵۰ppm（at over any ≥۱ms time interval) | ||
| Offset Range | ۲ns/div to 8ns/div; (-۸div x s/div) to 20ms; |
۲۰ns/div to 80us/div; (-8div x s/div) to 40ms; ۲۰۰us/div to 80s/div; (-8div x s/div) to 400s |
|
| Delta Time Measurement Accuracy (Full Bandwidth) |
Single-shot, Normal mode:± (۱ sample interval +100ppm × reading + 0.6ns); >16 averages:± (۱ sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ ۲۰۰ |
||
| Vertical | |||
| Vertical Resolution | ۸-bit resolution, all channel sampled simultaneously | ||
| Position Range | ۲mV/div to 20mV/div, ±۴۰۰mV; ۵۰mV/div to 200mV/div, ±۲V ۵۰۰mV/div to 2V/div, ±۴۰V; 5V/div to 10V/div, ±۵۰V |
||
| Bandwidth | ۷۰MHz | ||
| Rise Time at BNC( typical) | ۵ns | ||
| Math | +, -, *, /, FFT | ||
| FFT | Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman; ۱۰۲۴ sample point |
||
| Bandwidth Limit | ۲۰MHz | ||
| Low Frequency Response (-3db) | ≤۱۰Hz at BNC | ||
| DC Gain Accuracy | ±۳% for Normal or Average acquisition mode, 10V/div to 10mV/div; ±۴% for Normal or Average acquisition mode, 5mV/div to 2mV/div |
||
| DC Measurement Accuracy, Average Acquisition Mode |
When vertical displacement is zero, and N ≥۱۶:± (۳% × reading + 0.1div + 1mV) only 10mV/div or greater is selected; When vertical displacement is not zero, and N≥۱۶: ± [۳% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 10V/div |
||
| Volts Measurement Repeatability, Average Acquisition Mode |
Delta volts between any two averages of ≥۱۶ waveforms acquired under same setup and ambient conditions | ||
| Trigger System | |||
| Trigger Types | Edge, Video, Pulse, Slope, Over time, Alternative | ||
| Trigger Source | CH1, CH2, EXT, EXT/5, AC Line | ||
| Trigger Modes | Auto, Normal, Single | ||
| Coupling Type | DC, AC, Noise Reject, HF Reject, LF Reject | ||
| Trigger Sensitivity (Edge Trigger Type) |
DC(CH1,CH2): ۱div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; DC(EXT): ۲۰۰mV from DC to 100MHz; 350mV from 100MHz to 200MHz; DC(EXT/5): ۱V from DC to 100MHz;1.75V from 100MHz to 200MHz; AC: Attenuates signals below 10Hz; HF Reject: Attenuates signals above 80kHz; LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz |
||
| Trigger Level Range | CH1/CH2: ±۸ divisions from center of screen; EXT: ±۱٫۲V; EXT/5:±۶V |
||
| Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥۲۰ns | CH1/CH2: 0.2div × volts/div within ±۴ divisions from center of screen; EXT: ± (۶% of setting + 40mV); EXT/5: ± (۶% of setting + 200mV); |
||
| Set Level to 50%(typical) | Operates with input signals ≥۵۰Hz | ||
| Video Trigger | |||
| Video Trigger Type | CH1, CH2: Peak-to-peak amplitude of 2 divisions; EXT: 400mV; EXT/5: 2V |
||
| Signal Formats and Field Rates, Video Trigger Type | Supports NTSC, PAL and SECAM broadcast systems for any field or any line | ||
| Holdoff Range | ۱۰۰ns ~ 10s | ||
| Pulse Width Trigger | |||
| Pulse Width Trigger Mode | Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse | ||
| Pulse Width Trigger Point | Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width |
||
| Pulse Width Range | ۲۰ns ~ 10s | ||
| Slope Trigger | |||
| Slope Trigger Mode | Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope | ||
| Slope Trigger Point | Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope. |
||
| Time Range | ۲۰ns ~ 10s | ||
| Overtime Trigger | |||
| Over Time Mode | Rising edge or Falling edge | ||
| Time Range | ۲۰ns ~ 10s | ||
| Alternative Trigger | |||
| Trigger on CH1 | Internal Trigger: Edge, Pulse Width, Video, Slope | ||
| Trigger on CH2 | Internal Trigger: Edge, Pulse Width, Video, Slope | ||
| Trigger Frequency Counter | |||
| Readout Resolution | ۶ digits | ||
| Accuracy (typical) | ±۳۰ppm (including all frequency reference errors and ±۱ count errors) | ||
| Frequency Range | AC coupled, from 4Hz minimum to rated bandwidth | ||
| Signal Source | Pulse Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. Video Trigger mode: The Frequency Counter does not work. |
||
| Measure | |||
| Cursor Measurement | Voltage difference between cursors: △V Time difference between cursors: △T Reciprocal of △T in Hertz (1/ΔT) |
||
| Auto Measuerment | Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF | ||
| Display | |||
| Display Type | ۷ inch 64K color TFT (diagonal liquid crystal) | ||
| Display Resolution | ۸۰۰ horizontal by 480 vertical pixels | ||
| Display Contrast | Adjustable (16 gears) with the progress bar | ||
| Probe Compensator Output | |||
| Output Voltage( typical) | About 5Vpp into ≥۱MΩ load | ||
| Frequency(typical) | ۱kHz | ||
| Power Supply | |||
| Supply Voltage | ۱۰۰-۱۲۰VACRMS(±۱۰%), ۴۵Hz to 440Hz, CATⅡ ۱۲۰-۲۴۰VACRMS(±۱۰%), ۴۵Hz to 66Hz, CATⅡ |
||
| Power Consumption | <30W | ||
| Fuse | ۲A, T rating, 250V | ||
| Environmental | |||
| Temperature | Operating: 32℉ to 122℉ (۰℃ to 50℃); Nonoperating: -40℉ to 159.8℉ (-۴۰℃ to +71℃) |
||
| Cooling Method | Convection | ||
| Humidity | +۱۰۴℉ or below (+40℃ or below): ≤۹۰% relative humidity; ۱۰۶℉ to 122℉ (+۴۱℃ to 50℃): ≤۶۰% relative humidity |
||
| Altitude | Operating: Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet) |
||
| Mechanical | |||
| Size | Length 385mm, Width 200mm, Height 245mm | ||
| Weight | ۳٫۵KG(with Packing); ۲٫۰۸KG(without Packing） | ||
فروش اسیلوسکوپ ۷۰Mhz هانتک Hantek DSO5072P توسط موسسه تست ایران عرضه می شود .
جهت خرید اسیلوسکوپ ۷۰ مگاهرتز ۲ کانال هانتک Hantek DSO5072P با موسسه تست ایران تماس بگیرید .
نشانی : تهران – خیابان جمهوری ، نرسیده به پل حافظ ، ساختمان جمهوری ، طبقه ۲ ، واحد ۲۰۱
تلفن : ۰۲۱۶۶۷۲۹۶۵۳ – ۰۲۱۶۶۷۲۳۰۶۳ – ۰۹۱۰۲۱۹۷۵۴۲
برچسب: Hantek DSO5072P اسیلوسکوپ دیجیتال اسیلوسکوپ دیجیتال ۷۰مگاهرتز اسیلوسکوپ دیجیتال Hantek اسیلوسکوپ دیجیتال هانتک هنتک DSO5072P | سایر مشخصات | ||
|---|---|---|
|
||
مقررات ارسال نظر : فارسی بنویسید و از کیبورد فارسی استفاده کنید. نظرات خود را براساس تجربه و استفاده‌ی عملی و با دقت به نکات فنی ارسال کنید؛ بدون تعصب به محصول خاص، مزایا و معایب را بازگو کنید . بهتر است در نظرات خود از تمرکز روی عناصر متغیر مثل قیمت، پرهیز کنید. به کاربران و سایر اشخاص احترام بگذارید. پیام‌هایی که شامل محتوای توهین‌آمیز و کلمات نامناسب باشند، حذف می‌شوند.
برای ثبت دیدگاه، لازم است ابتدا وارد حساب کاربری خود شوید. اگر این محصول را قبلا از این فروشگاه خریده باشید، دیدگاه شما به عنوان مالک محصول ثبت خواهد شد.
محصولات مرتبط
کالاهایی که دیده‌اید
نقد و بررسی‌ها
هیچ دیدگاهی برای این محصول نوشته نشده است.