اسیلوسکوپ ۱۰۰مگاهرتز +فانکشن هانتک Hantek DSO2D10
اسیلوسکوپ ۱۰۰مگاهرتز +فانکشن هانتک Hantek DSO2D10
مشخصات :
- اسیلوسکوپ ۱۰۰ مگاهرتز ۲ کانال دیجیتال حافظه دار
- سرعت نمونه برداری ۱GSa/S
- دارای فانکشن ژنراتور ۲۵ مگا هرتز ۱۲ بیتی
- صفحه نمایشگر WVGA رنگی ۷ اینچ
- ۳۲ نوع اندازه گیری اتوماتیک
- قابل اتصال به کامپیوتر با پورت USB
- فانکشن FFT
- دارای حافظه داخلی ۸ مگا بایتی
- USB FLASH
- ضمانت : یک ساله تعمیر
مشخصات کامل اسیلوسکوپ ۱۰۰مگاهرتز +فانکشن هانتک Hantek DSO2D10 :
Model | DSO2D15 | DSO2D10 | DSO2C15 | DSO2C10 |
Bandwidth | ۱۵۰MHz | ۱۰۰MHz | ۱۵۰MHz | ۱۰۰MHz |
Oscilloscope channels | ۲CH | ۲CH | ۲CH | ۲CH |
Waveform generator | ۱CH | ۱CH | – | – |
Oscilloscope | ||||
Sample rate | ۱GSa/s (single channel) 500MSa/s (two channels) | |||
Acquisition | ||||
Normal | Sample data | |||
Peak-to-peak value | Display high frequency and random burr | |||
Average | Average waveform, times: ۴, ۸, ۱۶, ۳۲, ۶۴, ۱۲۸ | |||
High resolution | Up to 12bit | |||
Input | ||||
Input coupling | DC, AC, GND | |||
Input impedance | ۱MΩ±۲% ‖۲۰pF±۳pF | |||
Probe attenuation factor | ۱X, 10X, 100X, 1000X | |||
Voltage rating | ۳۰۰V CAT II | |||
Maximum input voltage | ۳۰۰VRMS (10X) | |||
Horizontal | ||||
Waveform interpolation | (sin x)/x | |||
Maximum record length | Single channel maximum ۸M | |||
Two channels maximum ۴M | ||||
Horizontal scale range | ۲ns/div~100s/div ۱, ۲, ۵ step by step | |||
Time base mode | Y-T, X-Y, Roll | |||
Zero offset | ±۰٫۵ div×minimum time base gear | |||
Sample Rate and Delay Time Accuracy | ±۲۵ppm | |||
Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy | single-shot, Normal mode ±(۱ sample interval+100ppm×reading+0.6ns) | |||
>۱۶ times averages ±(۱ sample interval+100ppm×reading+0.4ns) | ||||
Sample interval=sec/div÷۲۰۰ | ||||
Sample Rate and Delay Time Accuracy | ±۵۰ppm(at any interval greater than 1ms) | |||
Vertical | ||||
Model | DSO2D15 | DSO2D10 | DSO2C15 | DSO2C10 |
Bandwidth | ۱۵۰MHz | ۱۰۰MHz | ۱۵۰MHz | ۱۰۰MHz |
Rising time in BNC position (typical) | ۲٫۴ns | ۳٫۵ns | ۲٫۴ns | ۳٫۵ns |
Vertical resolution | ۸ bits resolution, each channel samples simultaneously | |||
Vertical sensitivity | ۲mV/div to 10V/div | |||
Offset range | ≥ ۲۰۰mV/div, ±۱V; | |||
<۲۰۰mV/div ±۵۰V | ||||
Mathematical operation | +, -, ×, ÷, FFT | |||
FFT | Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop | |||
Bandwidth Limit | ۲۰MHz | |||
Bass response(-۳db) | In BNC position ≤ ۱۰Hz | |||
Vertical gain accuracy | In ”normal” or ”average” acquisition mode, the accuracy of 10V/div to 10mV/div is ±۳%; | |||
In ”normal” or ”average” acquisition mode, the accuracy of 5mV/div to 2mV/div is ±۴% | ||||
Note: Bandwidth reduced to 6MHz when using a 1X probe | ||||
Trigger | ||||
Trigger type | Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC | |||
Trigger level range | ±۵ divisions from the center of the screen | |||
Trigger mode | Auto, Normal, single | |||
Level | CH1~CH2 | ±۴ divisions from the center of the screen | ||
EXT(Only With AWG Model) | ۰~۳٫۳V | |||
Holdoff range | ۸ns~10s | |||
Trigger level accuracy | CH1~CH2 | ۰٫۲ div×volts/div within ±۴ divisions from the center of the screen | ||
EXT(Only With AWG Model) | ±(Set value× ۶%+۴۰mV) | |||
Edge trigger | Slope | Rising edge, falling edge, rising or falling edge | ||
Signal source | CH1, CH2, EXT(Only With AWG Model) | |||
Pulse width trigger | Polarity | Positive polarity, negative polarity | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2, | |||
Pulse width range | ۸ns ~ 10s | |||
Accuracy | ۸ns | |||
Video trigger | Signal standard | NTSC, PAL | ||
Signal source | CH1~CH2 | |||
Synchronization | Scanning line, line number, odd field, even field, all field | |||
Slope trigger | Slope | rising, falling | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1 ~ CH2 | |||
Time range | ۸ns ~ 10s | |||
Accuracy | ۸ns | |||
Overtime trigger | Signal source | CH1~CH2, | ||
Polarity | Positive polarity, negative polarity | |||
Time range | ۸ns ~ 10s | |||
Accuracy | ۸ns | |||
Window trigger | Signal source | CH1~CH2 | ||
Pattern trigger | Pattern | ۰: low level; 1: high level; X: ignore | ||
Level(signal source) | CH1~CH2 | |||
Interval trigger | Slope | rising, falling | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2 | |||
Time range | ۸ns ~ 10s | |||
Accuracy | ۸ns | |||
Under Amp trigger | Polarity | Positive polarity, negative polarity | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2 | |||
Time range | ۸ns ~ 10s | |||
Accuracy | ۸ns | |||
UART trigger | Condition(When) | Start, Stop, data, Parity ERR, COM ERR | ||
Signal source(RX/TX) | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Data length | ۱ byte | |||
Data bit width | ۵ bit, 6 bit, 7 bit, 8 bit | |||
Odd-even check | none, odd, even | |||
Idle level | high, low | |||
Baud rate (optional) | ۱۱۰/۳۰۰/۶۰۰/۱۲۰۰/۲۴۰۰/۴۸۰۰/۹۶۰۰/۱۴۴۰۰/۱۹۲۰۰/۳۸۴۰۰/۵۷۶۰۰/۱۱۵۲۰۰/۲۳۰۴۰۰/۳۸۰۴۰۰/۴۶۰۴۰۰ bit/s | |||
Baud rate(user-defined) | ۳۰۰bit/s~334000bit/s | |||
LIN trigger | Condition(When) | Interval field, synchronization field, ID field, synchronization error, identifier, ID and data | ||
Signal source | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Baud rate (optional) | ۱۱۰/۳۰۰/۶۰۰/۱۲۰۰/۲۴۰۰/۴۸۰۰/۹۶۰۰/۱۴۴۰۰/۱۹۲۰۰/۳۸۴۰۰/۵۷۶۰۰/۱۱۵۲۰۰/۲۳۰۴۰۰/۳۸۰۴۰۰/۴۶۰۴۰۰ bit/s | |||
Baud rate(user-defined) | ۳۰۰bit/s~334000bit/s | |||
CAN trigger | Condition(When) | Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame | ||
Signal source | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Baud rate (optional) | ۱۰۰۰۰, ۲۰۰۰۰, ۳۳۳۰۰, ۵۰۰۰۰۰, ۶۲۵۰۰, ۸۳۳۰۰, ۱۰۰۰۰۰, ۱۲۵۰۰۰, ۲۵۰۰۰۰, ۵۰۰۰۰۰, ۸۰۰۰۰۰, ۱۰۰۰۰۰۰ | |||
Baud rate(user-defined) | ۵kbit/s~1Mbit/s | |||
SPI trigger | Signal source | CH1~CH2 | ||
Data format | Hex (hexadecimal) | |||
Data bit width | ۴, ۸, ۱۶, ۲۴, ۳۲ | |||
IIC trigger | Signal source (SDA/SCL) | CH1~CH2 | ||
Data format | Hex (hexadecimal) | |||
Data index | ۰~۷ | |||
When(condition) | Start bit, stop bit, No Ack, address, restart, address and data | |||
Measurement | ||||
Cursor | Voltage difference between cursors △V | |||
Time difference between cursors △T | ||||
Reciprocal of △T, in Hertz (1/△T) | ||||
Auto measurement | frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, – width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, – duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF | |||
DVM | Data source | CH1, CH2 | ||
Measurement type | DC RMS | |||
AC RMS | ||||
DC | ||||
Frequency meter | hardware 6 bits frequency meter | |||
Arbitrary waveform generator | ||||
Channel | ۱ | |||
Sample rate | ۲۰۰MSa/s | |||
Vertical resolution | ۱۲ bits | |||
Maximum frequency | ۲۵ MHz | |||
Standard waveforms | sine, square, ramp,Exp, noise, DC | |||
Arbitrary waveform | Arb1, Arb2, Arb3, Arb4 | |||
Sin | Frequency range | ۰٫۱Hz~25MHz | ||
Square/pulse | Frequency range | ۰٫۱Hz~10MHz | ||
Triangular wave | Frequency range | ۰٫۱Hz~1MHz | ||
Sampling wave | Frequency range | ۰٫۱Hz~1MHz | ||
Index | Frequency range | ۰٫۱Hz~5MHz | ||
Noise | ||||
Arb1 | Frequency range | ۰٫۱ Hz to 10 MHz | ||
Arb2 | Frequency range | ۰٫۱ Hz to 10 MHz | ||
Arb3 | Frequency range | ۰٫۱ Hz to 10 MHz | ||
Arb4 | Frequency range | ۰٫۱ Hz to 10 MHz | ||
Waveform length | ۸KSa | |||
Frequency | Accuracy | ۱۰۰ ppm (<10 kHz) 50 ppm (>10 kHz) | ||
Resolution | ۰٫۱ Hz or 4 bits,take the greater one | |||
Amplitude | Output range | ۱۰mV~7Vp-p (high impedance) | ||
۵mV~3.5Vp-p (50Ω) | ||||
DC offset | Range | ±۳٫۵ V, high impedance | ||
±۱٫۷۵ V, 50 Ω | ||||
Resolution | ۱۰۰ μV or 3 bits, take the greater one | |||
Accuracy | ۲% (۱ kHz) | |||
Output impedance | ۵۰ Ω | |||
General specifications | ||||
Display | Display type | ۷” diagonal TFT liquid crystal | ||
Display resolution | ۸۰۰ (horizontal)*480 (vertical) pixels | |||
Display colour | ۱۶ million colours (24 bits true colour) | |||
Persistence time | minimum, ۱ s, 5 s, 10 s, 30 s, infinite | |||
Display type | dot, vector | |||
Display brightness | adjustable | |||
Grid type | adjustable | |||
Grid brightness | adjustable | |||
Interface | Standard interface | USB Host,USB Device | ||
General specifications | Probe compensator output | |||
Output voltage, typical | about 2Vpp input ≥۱MΩ load | |||
Frequency, typical | ۱kHz | |||
Power supply | ۱۰۰-۱۲۰VACRMS(±۱۰%), ۴۵Hzto 440Hz, CATⅡ | |||
۱۲۰-۲۴۰VACRMS(±۱۰%), ۴۵Hz to 66Hz, CATⅡ | ||||
Power consumption | <30W | |||
Fuse | T, 3.15A, 250V, 5x20mm | |||
Operating temperature | ۰~۵۰ °C (32~122 °F) | |||
Storage temperature | -۴۰~+۷۱ °C (-40~159.8 °F) | |||
Humidity | ≤+۱۰۴℉(≤+۴۰°C): ≤۹۰% relative humidity | |||
۱۰۶℉~۱۲۲℉ (+۴۱°C ~50°C): ≤۶۰% relative humidity | ||||
Altitude | Operating and nonoperating | ۳, ۰۰۰m (10, 000 feet) | ||
Mechanical shock | Random vibration | ۰٫۳۱ g RMS from 50Hz to 500Hz, | ||
۱۰ minutes on each axis | ||||
Nonoperating | ۲٫۴۶g RMS from 5Hz to 500Hz, | |||
۱۰ minutes on each axis | ||||
Operating | ۵۰g, 11ms, half-sine wave | |||
Mechanical | Size | ۳۱۸ x 110 x 150mm (length x width x height) | ||
Weight | ۱۹۰۰g |
برچسب: Hantek DSO2D10 اسیلوسکوپ 100مگاهرتز +فانکشن هانتک Hantek DSO-2D10 هانتک Hantek DSO-2D10
نقد و بررسیها
هیچ دیدگاهی برای این محصول نوشته نشده است.